This 3 piece professional terminal cleaning kit may be used for small, medium and larger male and female electrical connector terminals to assist the technician in cleaning and eliminating the effects of poor terminal connections on the modern automotive vehicle, without the terminal removal from the connector.
Made from quality stainless steel and utilising an abrasive material to clean the corroded terminal surface, the EQP-026 is suitable for the following application examples:
- Connector terminals on automotive control units and ignition components.
- Wiring harness connector joints.
- Engine management sensors and connectors.
- Relay terminals and connectors.
- Fuse sockets.
- ABS sensors and control modules.
- Other typical automotive terminals that are potentially exposed to all weather conditions.
- Stainless steel material with abrasive coated terminal tip. Diamond abrasive material on the tweezers for removing corrosion on any terminal type.
Length: 20 mm
Width: 135 mm
Height: 135 mm
Operating instructionsFor male terminals: Select a suitably sized terminal cleaner as required.
Grip the terminal using the tweezer action and allow the abrasive material to remove any corrosion as the tool is pulled away from the terminal. Repeat as required.
For female terminals: Select a suitably sized terminal cleaner as required.
Slide the abrasive tip of the tool into the terminal and remove it gently to prevent any terminal expansion.
Precautions: Ensure all power supply is disconnected before any work is carried out on the circuit.
A suitable terminal cleaner may be used to flush any oil or corrosion residue from the connector and terminal assembly.
A suitable protective film may also be used to prevent further corrosion.
- EQP-016 Ignition Quick Probe – Coil Over Plug – KV and ARC Tester with Variable Sensitivity
- EQP-017 Ignition Quick Probe – KV and ARC Tester
- EQP-018 Automotive Relay Tester
- EQP-019 Hybrid Circuit Tester 12-42 Volt
- EQP-021 Vacuum Pump and Brake Bleeding Kit
- EQP-023 Oil Pressure Test Kit
- EQP-025 Electronic Fuel Injector Probe
- EQP-028 Dynamic DC Volt Probe
- EQP-100 Fuel Pressure and Flow Test Kit
- EQP-101 Oxygen Sensor Tester
- EQP-102 Automotive Multimeter and Infrared Thermometer
- EQP-105 Noid Light Set
- EQP-106 Electrical Test Connector Set – 28-Piece
- EQP-107 Common Rail Diesel Injector Return Flow Tester
- EQP-109 Relay Bypass Switch Master Kit
- EQP-110 Pierburg Fuel Pump Bench Tester
- EQP-111 Wheel Speed Sensor and Circuit Tester
- EQP-112 Off Car Ignition Coil Tester
- EQP-113 12 Volt Battery Tester
- EQP-114 Battery and Electrical System Tester with Printer
- EQP-115 Electronic EGR, Throttle Body & Actuator Tester
- EQP-117 Fuse Current Tester
- EQP-119 OBD11 Code Reader and Reset Tool
- EQP-120 Hand Held OBDII Scan Tool
- EQP-121 OBDMATE Code Reader and Reset Tool
- CPS-000 Connector and Harness Repair Kit
- EQP-001 Quick-Snap Connector Tool Kit
- EQP-002 Fuel Injector Filter Removal Tool
- EQP-004 Electrical Terminal Release Kit – 23 Piece
- EQP-015 Fuel Line Stopper Set – 12 Piece
- EQP-020 Hose Clamp Pliers
- EQP-022 Spark Plug Gauge
- EQP-024 Power Tool & Security Bit Set
- EQP-026 Terminal Cleaning Kit
- EQP-027 Pocket LED Magnetic Work Light
- EQP-122 Power Boost + Power Bank
- FSA-007 Fuel Line Repair Kit
- IJK-000 Fuel Injector Service Kit
- EQP-003 Installation Tool for Fuel Pumps
- EQP-005 Bosch AFM Extractor Tool
- EQP-006 Pierburg AFM Extractor Tools
- EQP-007 Oxygen Sensor Removal Tool 22mm (7/8”)
- EQP-008 Oxygen Sensor Wrench – 12 Point and 6 Point
- EQP-009 Oxygen Sensor Wrench – 12 Point and 6 Point – 54mm (2 1/8″) Offset
- EQP-010 Oxygen Sensor Wrench – Shielded Applications
- EQP-011 Oxygen Sensor Wrench – Standard Oxygen Sensors
- EQP-012 Oxygen Sensor Wrench – 6 Point with 9.5mm (3/8″) Drive
- EQP-013 Oxygen Sensor Thread Chaser
- EQP-014 Oxygen Sensor Thread Repair Kit
- EQP-029 Fuel line Removal and Fitting Tool
- EQP-030 Fuel Tank Lock Ring Removal Tool Kit
- EQP-031 VAG Ignition Coil Puller Kit
- REL-000 Relay Replacement Kit
- Where to Buy